Fundamental Plumber Insights for Bathtub Installation
Fundamental Plumber Insights for Bathtub Installation
Blog Article
What're your thoughts about Tools You Need to Install a New Bathtub ?
Installing a bath tub isn't precisely rocket science, yet it does need solid plumbing, woodworking, as well as in some cases, tiling abilities. Replacing an old tub with a new one is likewise a reasonably challenging project. If the old tub is readily obtainable, the task can relocate immediately; if you have to open up a wall to eliminate the old tub and place the brand-new bath tub, the task is a lot harder. In either situation, the task is within a residence handyman's abilities, although you will require a helper to leave the old tub as well as set in the new one. Ensure you have certified on your own for the work as well as are comfortable attempting it. Rather than hiring a specialist to take control of a halfway-completed project, it is much better to consider utilizing one prior to you start. Chances are you may need an expert plumber to make tube links.
This write-up will certainly assist you mount a new bath tub in your restroom if you have actually already gotten a new tub and do not need to transform the arrangement of your previous water pipes.
Your tools and also material checklist ought to comprise the following:
Removing Old Touches
If you require to change old taps with new ones as a part of your setup, after that the first thing you should do is disconnect the supply of water. After doing so, activate the taps to drain pipes any kind of water staying in the system. The procedure of removing the existing taps can be quite bothersome as a result of the limited gain access to that is commonly the instance.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipes to the faucets. Have a fabric all set for the continuing to be water that will certainly originate from the pipes. As soon as the supply pipes have been eliminated, make use of the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the single taps from turning during this process. As soon as the faucets have actually been removed, the holes in the bath/basin will have to be cleaned up of any kind of old securing substance.
Before going on to fit the brand-new faucets, compare the pipeline links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the new faucets to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to stop damages to the string. One end of the connector fits on the plastic tail of the tap and also the other end supplies a connection to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly require reducing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, position the faucet in the placing hole in the bath/basin making certain that the washing machines are in place in between the tap and the sink. Protect the tap in place with the producer offered backnut. Once the tap is securely in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with normal faucet ports. The former kind must be connected to the faucet ends first, tightening up only by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been attached.
Installing the Tub
Making use of the two wooden boards under its feet, position the bathtub in the needed setting. The wooden boards are handy in equally spreading out the weight of the bathtub over the area of the boards instead of concentrating all the weight onto four small factors.
The next goal is to guarantee that the bath tub is leveled all round. This can be attained by checking the spirit level and also readjusting the feet on the bathtub until the spirit level checks out degree.
To mount taps, fit the bottom of the furthest versatile faucet connector to the suitable supply pipe by making a compression sign up with; after that do the very same for the various other faucet.
Turn on the water system and examine all joints and also new pipework for leakages as well as tighten them if required. Load the tub and likewise check the overflow electrical outlet and the regular outlet for leaks.
Ultimately, repair the bathroom paneling as described in the maker's instruction manual. Tiling as well as securing around the bath tub ought to wait up until the bath tub has actually been used a minimum of when as this will certainly resolve it into its final position.
Getting ready for the Installment
To start with, the sustaining framework provided with the bath must be fitted (if required) according to the maker's instructions. Next, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is essential to make sure that if the faucet includes a plastic washing machine, it is fitted in between the bathroom as well as the faucets. On a plastic bath, it is additionally practical to fit a sustaining plate under the taps system to avoid strain on the bath tub.
Fit the adaptable tap connectors to the bottom of the two faucets utilizing 2 nuts as well as olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet with the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bath. Ensure you use every one of the supplied washers.
Attach the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom need to now prepare to be fitted in its last setting.
Tiling Around the Tub
In the location where the bath fulfills the ceramic tile, it is needed to seal the accompanies a silicone rubber caulking. This is very important as the fitting can relocate enough to split a rigid seal, creating the water to pass through the wall surface between the bathroom and also the tiling, bring about difficulties with moisture and also possible leakages to the ceiling below.
You can choose from a range of coloured sealants to assimilate your fixtures and installations. They are offered in tubes and cartridges, and can securing spaces approximately a width of 3mm (1/8 inch). If you have a larger void to fill, you can load it with twists of soaked newspaper or soft rope. Bear in mind to always fill up the bath tub with water prior to sealing, to enable the activity experienced when the bathtub is in use. The sealant can split rather early if you do not take into consideration this activity prior to securing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are additionally easily offered on the marketplace. It is a good idea to fit the tiles utilizing water-resistant or water-proof sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a passionate reader on How to Install a Bathtub, I figured sharing that section was essential. Are you aware of someone else who is occupied with the subject? Do not hesitate to promote it. I value reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Plumbing insights available. Report this page